מדריך וקבצים להתקנת אניגמה 2 של SIFTEAM

[prince_amir]

הנה מדריךשמסביר איך להתקין את האימג של SIFTEAM אניגמה 2, יש בשימוש NFS SERVER או דרך USB, בכל מקרהף המדריך הוא מאתר של SIFTEAM.

אני רוצה לציין כי התוכנה עולה או דרך שרת NFS או דרך DISK ON KEY, ההסבר פה הוא איך להפעיל את האימג בשני הדרכים

הקבצים ניתנים להורדה ישירות מהלינק הנל לפי סוג הממיר
http://enigma2.sifteam.eu/index.php?dir ... m%200.2.0/

ABOUT ENIGMA 2 for ipbox9000/900/910/cuberevo/cuberevo-mini:
-------------------------------------------------------------

This is an adaption of Enigma 2 for the DGStation's High Definition boxes.

I want to thank these people:
Team DuckTales: for helping me on finding really many bugs and to helping me on make Enigma2 like it is now.
zbigzbig20, crashs: for default bootlogo
Spaeleus: for Italian translation
SIFTeam: this is my place, with all my friends that i like really to chat with!!!! (I LOVE YOU GUYS)

I want also to thank two special friends:
genge: for be the best betatester of ever!!!!! (really a ball breaker but also a good friend )
PhotosOfGhosts: for helping me on finding, studying and solving bugs

Regards, Tideglo

----------------
HOW TO INSTALL:
----------------

To test this enigma2 image you need a running nfs server and a serial & network
connection to the receiver.

You need uboot 1.3.1 or higher to run e2 (never tested with lower versions)

Do this only if you want to use nfs-server otherwise go to point 3:
1. extract the tgz file on the server and set the directory in /etc/exports
for example:
/root/Desktop/root 192.168.1.0/255.255.255.0(rw,no_root_squash,sync,no_subtree_ch eck)

where 192.168.1.0 is your net base-address and 255.255.255.0 is your netmask

2. restart nfs server

3. connect via serial console with an hyperterminal connection to the receiver (I suggest you to use putty, it's freeware, and configure it to use a 115200 serial connection)

4. turn on the receiver and hit ctr+z in serial console
you should see the following prompt:

cuberevo>

5. customize the following settings to your network environment and type them into the
serial console:

setenv menu_1 'setenv ipaddr 192.168.1.5;setenv serverip 192.168.1.6;setenv gateway 192.168.1.1;setenv netmask 255.255.255.0;setenv bootargs "console=ttyAS1,115200 panic=3 root=/dev/nfs nfsroot=/root/Desktop/root rw rootpath=/root/Desktop/root ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 init=/bin/devinit";setenv bootcmd "nfs a5ff0000 192.168.1.6:/root/Desktop/root/boot/uImage;bootm a5ff0000";saveenv;boot'

setenv menu_2 'setenv ipaddr 192.168.1.5;setenv serverip 192.168.1.6;setenv gateway 192.168.1.1;setenv netmask 255.255.255.0;setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 panic=3 root=/dev/sda1 rw rootdelay=10 init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";setenv bootcmd "run bootusb";saveenv;boot'

setenv menu_3 'setenv ipaddr 192.168.1.5;setenv serverip 192.168.1.6;setenv gateway 192.168.1.1;setenv netmask 255.255.255.0;setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargsusb "setenv bootargs console=ttyAS1,115200 panic=3 root=/dev/sdb1 rw rootdelay=10 init=/bin/devinit ip=$ipaddr:$serverip:$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";setenv bootcmd "run bootusb";saveenv;boot'

setenv menu_4 'setenv ipaddr 192.168.1.5;setenv serverip 192.168.1.6;setenv gateway 192.168.1.1;setenv netmask 255.255.255.0;setenv bootargs "console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 bigphysarea=1500 ip=$ipaddr:$serverip:$gateway:$netmask quiet";setenv bootcmd "bootm a0060000";saveenv;boot'

saveenv


remember to customize where /root/Desktop/root is the directory you added to /etc/exports and ipaddr is the ip of your decoder, serverip is the ip of your nfs-server, gateway is your gateway ip, netmask is the mask of your home-net

6. now you can restart your decoder and press the relative remote controller's button for 5 seconds to start the image you want:

Press Button 1: start your image using nfs-server
Press Button 2: start your image using usb pendrive if you don't have a SATA hdd
Press Button 3: start your image using usb pendrive if you have a SATA hdd
Press Button 4: start your original flash image in the decoder (DGStation's original firmwares and images based on them)

That operation is necessary only the first time you want to change your boot commands. You don't need to press all the time you reboot the decoder a button to select wich image to start, simply do that only if you want to change to e2 nfs from usb, or from original images.

That's all, Tideglo


Mini How to for Usb users:

English

1) connect the pen to the 9000
2) format the pen usb as for move var
3) disconnect and reconnect eh pen (so the decoder see it)
4) copy with FTP the file tar.gz in /mnt/usb
5) enter in telnet
6) write cd /mnt/usb
7) write tar xzf nomedelfile.tar.gz


For Flash Users:

English



To flash your stb use: rename firmware in usb_update.img and use usb stick with standard flash method . For ipbox9000 you can also use Flashtools and usb cable
set bootargs in this way:

codice:
setenv bootargs console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 mem=128m ip=192.168.1.150:192.168.1.111:192.168.1.1:255.255 .255.0 coprocessor_mem=4m@0x10000000,4m@0x10400000

after write saveenv and reboot your stb.That's all

192.168.1.150 is my lan ip (decoder)
192.168.1.111 is my serveripaddress (you can set standard value,it's not important)
192.168.1.1 is my gateway ip (my router)
255.255.255.0 this is netmask


that's all
Thanks to all Sifteam staff
SIF TeAm Forum

לינק הסבר מאתר SIFTEAM

[prince_amir]

הנה הסבר יותר פשוט, כנראה שעדיף לטעון עם USB

I think version for USB STICK is the best choice. We have E2 on USB and in flash latest dgs sw (or alternative sw based on dgs) We can easly switch beetwen flash or usb image.

How to install E2 on usb stick? This is very simple. Just for example connect your usb stick to your PC, format it in "Paragon Partition Manager" to ext2 or ext3 (both fs working with latest e2) After this turn off your Ipbox HD to deep standby (or turn off by rear power button) Now connect your formatted usb stick to Ipbox and turn on your Ipbox HD. Now after Ipbox mount your usb stick connect with your box by FTP, enter to mnt/usb , now copy there your E2 image in tar.gz file (you can rename it for example to enigma2beta2.tar.gz) after copy connect with your box by telnet and write:

Quote:
cd /mnt/usb/ [ENTER]
tar xzvf enigma2beta2.tar.gz [ENTER]


(ofcourse press [ENTER] on your keyboard after commad do not write this

Now wait when it install it. You will see small progress thanks to command xzvf (latest file after install on list will be README.

After install turn off your Ipbox HD to deep standby , turn on and if you changed bootargs in uboot press by 5sec for example button 3 then E2 will boot from usb with SATA HDD support. Now wait 2 minutes Then have fun