Titanium how to......
נשלח: 22 פברואר 2004, 12:49
These are very, very basic steps that should help anyone who gets the same problems that I had.
To update your Titanium card, if it has OS 01.04 installed and the Titanium Card Progger
will not update to OS 01.05 or/and OS 01.06…
You’ll need to first downgrade to OS 01.03 before you can upgrade
Except Titanium Card Progger V1.9.0,
you’ll need the files included in the file Titanium_ATR_OS13.zip
titanium_atr_os13.eep and
titanium_atr_os13.hex
Steps:
1) Start Titanium Card Progger V1.9.0 and put your Titanium Card in the programmer.
2) Press the green arrow button to connect the programmer. (You’ll get some message about OS)
3) Erase your card (Press the Erase-Button) ("Titanium1 SmartKey Card OS Version 01.04 found").
4) Load the file titanium_atr_os13.hex (Press Load.hex-Button).
5) Load the file titanium_atr_os13.eep (Press Load.eep-Button).
6) Press the Burn it!-Button to downgrade the card down to OS 01.03 .
7) Disconnect (press the red arrow button).
8) Reconnect (press the green arrow button) ("Titanium1 SmartKey Card OS Version 01.03 found").
9) The Titanium Card Progger should ask you about updating the OS...
10) Press "YES" (this will upgrade from 01.03 to 01.04 to 01.05 , takes about 2 min).
11) The Titanium Card Progger then asks you about updating the OS from 01.05 to 01.06 .
12) Press "YES" (this will upgrade from 01.05 to 01.06 , takes about 1 min).
13) Now your card will be ready to program.
14) Press the Load.hex-Button and choose your conax flash.hex-file.
15) Press the Load.eep-Button and choose your conax eep-file.
(Preferably the one with key 20 & 21, for now that is 2004-02-04)
16) If you have a CryptKey.hex-file then press the Load cr.key-Button to load it (option).
17) Press the Burn it!-Button to program your card.
Done !
Enjoy your decrypted channels !!
If still you don’t get any picture and you know that your files are up to date.
Try shutting off the sat reciever, wait about 10 sec. And then turn it on again.
That helped me when I had that same problem. It resets the reciever and the cam
To update your Titanium card, if it has OS 01.04 installed and the Titanium Card Progger
will not update to OS 01.05 or/and OS 01.06…
You’ll need to first downgrade to OS 01.03 before you can upgrade
Except Titanium Card Progger V1.9.0,
you’ll need the files included in the file Titanium_ATR_OS13.zip
titanium_atr_os13.eep and
titanium_atr_os13.hex
Steps:
1) Start Titanium Card Progger V1.9.0 and put your Titanium Card in the programmer.
2) Press the green arrow button to connect the programmer. (You’ll get some message about OS)
3) Erase your card (Press the Erase-Button) ("Titanium1 SmartKey Card OS Version 01.04 found").
4) Load the file titanium_atr_os13.hex (Press Load.hex-Button).
5) Load the file titanium_atr_os13.eep (Press Load.eep-Button).
6) Press the Burn it!-Button to downgrade the card down to OS 01.03 .
7) Disconnect (press the red arrow button).
8) Reconnect (press the green arrow button) ("Titanium1 SmartKey Card OS Version 01.03 found").
9) The Titanium Card Progger should ask you about updating the OS...
10) Press "YES" (this will upgrade from 01.03 to 01.04 to 01.05 , takes about 2 min).
11) The Titanium Card Progger then asks you about updating the OS from 01.05 to 01.06 .
12) Press "YES" (this will upgrade from 01.05 to 01.06 , takes about 1 min).
13) Now your card will be ready to program.
14) Press the Load.hex-Button and choose your conax flash.hex-file.
15) Press the Load.eep-Button and choose your conax eep-file.
(Preferably the one with key 20 & 21, for now that is 2004-02-04)
16) If you have a CryptKey.hex-file then press the Load cr.key-Button to load it (option).
17) Press the Burn it!-Button to program your card.
Done !
Enjoy your decrypted channels !!
If still you don’t get any picture and you know that your files are up to date.
Try shutting off the sat reciever, wait about 10 sec. And then turn it on again.
That helped me when I had that same problem. It resets the reciever and the cam
