חדשות לגבי HUMAX 5400
נשלח: 12 אפריל 2004, 00:00
גירסה עדכנית לגבי HUMAX 5400
עובד ללא כרטיס
יש גם שיטוף כרטיסים ניסויני
-------------------------------------------------------------------------------------
ToH 3.2 with EMU 1.2 (by HoT)
Following CAS-systems become presently emuliert:
- IRDETO/BC - SECA with - SECA2 for Ident 64 - VIA - NAGRA with AU - CONAX
To the installation would note please following steps:
The HDF-file HoTEmu****.HDF consists of the basis firmware and the ToH-modules, like also the Emu. The
HDF-file is balanced out like usually with the download tool WDN40AK +.
After the HDF was loaded in the Humax, also the EmuKey-filed in the Humax must. Used to this 9500 EMU Ed23.exe". Attention, the Humi must not be turned on hiefür, therefore in the Standby. For letter would use the Button "Write". Please would test written arrived is in that 1st once with "Read", whether that
Key-filed also in the Humax. Under WIN2000, it seems to give there problems. After the store, one should bring the Humax an once in the Standby. First then the Keyfile is written out of the RAM into the Flash.
Attention! After the store of new canal-Settings, the EmuKey-filed must become again high store. It one would be used then humane from version 0.9.9.1. Humane was adapted specially on the HoT-firmware and
transfers no more basis parameter.
Attention! Presently a card in the internal CAM vorhaneden must be always, that includes at least the
Karteninitalisierung. However also an official Irdeto can or Betacryptkarte used become, that is queried also in
the EMU-fashion to the decoding.
In the Emu-fashions, one arrives over the ToH-Config menu. Under "Preselect", following attitudes are
possible:
EMU-K (Emulator and card) : ---------------------------.
In this fashion, ECM/EMM go' s both at the EMU and at the card. The card receives only ECM/EMM' s that through that 2. Irdetokennung of the card determined
are.
EMU-S (Emulator and Sharingserver for PW) : ------------------------------------------ .
In this fashion, another Sharing-server is included in addition into the communication. The connection takes
place via the serial interface at the Humax.
Advance:
1St Vebinde Cardreader at the PC (z. B. COM1) and Humax at at COM2 2. start CardServer 3. Settings: Add Reader,
set IP 0.0.0.0 (for server and client at the same PC)
4Th start CardServer again 5. premiere-Smartcard put away and test CardServer-Window 6. starting of HSIC: adjust
server-ip (=127.0.0.1) tcp-port and com-port
7Th Reset embedded HUMAX-CAM (0-RCL)
EMU (pure EMU fashion) : -------------------. This fashion not yet is transferred. Here it should be once possible to
activate the EMU without the putting away of a card.
PMCT ----.
In the PMCT, the CAS-systems can serve should that of the EMU under EMU-K, EMU-S and EMU, registered become.
Simply so let.
Much joke wishes the HoT-team
עובד ללא כרטיס
יש גם שיטוף כרטיסים ניסויני
-------------------------------------------------------------------------------------
ToH 3.2 with EMU 1.2 (by HoT)
Following CAS-systems become presently emuliert:
- IRDETO/BC - SECA with - SECA2 for Ident 64 - VIA - NAGRA with AU - CONAX
To the installation would note please following steps:
The HDF-file HoTEmu****.HDF consists of the basis firmware and the ToH-modules, like also the Emu. The
HDF-file is balanced out like usually with the download tool WDN40AK +.
After the HDF was loaded in the Humax, also the EmuKey-filed in the Humax must. Used to this 9500 EMU Ed23.exe". Attention, the Humi must not be turned on hiefür, therefore in the Standby. For letter would use the Button "Write". Please would test written arrived is in that 1st once with "Read", whether that
Key-filed also in the Humax. Under WIN2000, it seems to give there problems. After the store, one should bring the Humax an once in the Standby. First then the Keyfile is written out of the RAM into the Flash.
Attention! After the store of new canal-Settings, the EmuKey-filed must become again high store. It one would be used then humane from version 0.9.9.1. Humane was adapted specially on the HoT-firmware and
transfers no more basis parameter.
Attention! Presently a card in the internal CAM vorhaneden must be always, that includes at least the
Karteninitalisierung. However also an official Irdeto can or Betacryptkarte used become, that is queried also in
the EMU-fashion to the decoding.
In the Emu-fashions, one arrives over the ToH-Config menu. Under "Preselect", following attitudes are
possible:
EMU-K (Emulator and card) : ---------------------------.
In this fashion, ECM/EMM go' s both at the EMU and at the card. The card receives only ECM/EMM' s that through that 2. Irdetokennung of the card determined
are.
EMU-S (Emulator and Sharingserver for PW) : ------------------------------------------ .
In this fashion, another Sharing-server is included in addition into the communication. The connection takes
place via the serial interface at the Humax.
Advance:
1St Vebinde Cardreader at the PC (z. B. COM1) and Humax at at COM2 2. start CardServer 3. Settings: Add Reader,
set IP 0.0.0.0 (for server and client at the same PC)
4Th start CardServer again 5. premiere-Smartcard put away and test CardServer-Window 6. starting of HSIC: adjust
server-ip (=127.0.0.1) tcp-port and com-port
7Th Reset embedded HUMAX-CAM (0-RCL)
EMU (pure EMU fashion) : -------------------. This fashion not yet is transferred. Here it should be once possible to
activate the EMU without the putting away of a card.
PMCT ----.
In the PMCT, the CAS-systems can serve should that of the EMU under EMU-K, EMU-S and EMU, registered become.
Simply so let.
Much joke wishes the HoT-team
